top of page
IMG_3908.JPG

101 Series

Because of the design and arrangement of the rolls the WDM 101 series pinch pyramid bending roll is a very versatile plate roll. Because of the large openings between the rolls symmetrical structural sections can be rolled without additional attachments, square and rectangle tubing, channel leg in/out, I-beam on flange, and fabricated panels. In the forming operation both the leading and trailing edges can be performed with one entry of the workpiece into the machine. This eliminates the necessity of manipulating and turning the workpiece for a double entry as is required on an initial pinch type machine.

Standard Features
  • 1045 steel rolls machined to T63 micro inch finish

  • Crowned rolls

  • Total hydraulic operation

  • Instant start/stop/reverse

  • 3 roll drive

  • 3 phase 230/460 volts, 60HZ electrics

  • Electrics to NFPA-79 specifications 24VDC control circuit

  • Safety/Emergency stop cable on 3 sides of the machine

  • Overload protected

  • TEFC main motor

  • Quiet hydraulic system

  • Haze gray epoxy and blue enamel finish (V.O.C. compliant)

  • Sealed spherical roller bearings on all main points

  • 1 squaring groove in far roll

  • Rolls tilt for cone rolling

  • Rolls driven through efficient spur gear drives or planetary speed reducers

  • Roving pendant control

  • DRO to show roll position

  • Hydraulically actuated drop-end

  • Accurately machined, compact, streamlined, and all welded steel frame

  • Variable roll speed 0-22 FPM

  • 1 year warranty

  • Made in USA

Options
  • Hardened only rolls 55-60 Rc. (1045 flame hardened) T63 finish

  • Hardened and polished rolls 55-60 Rc. (1045 flame hardened) G32 finish

  • Other alloys and finishes are available

  • Additional squaring grooves in lower rolls

  • Circular grooves in rolls for rolling rods or sheets with wire edges 3/8, 1/2, and 5/8

  • Other special circular grooves for extrusions etc.

  • Forward & reverse guarded foot pedal for roll rotation

  • Cone attachment

  • Control upgrade

  • Non-electric version

  • Side supports

  • Overhead supports

  • Feed tables

  • Ejectors

  • Special electrics

  • Special customer supplied paint

  • Light curtain safety guarding

Also Available

  • Chromed rolls

  • Special extra smooth rolls

  • Special grooves in rolls

  • High-speed version

Rolls

All the rolls are accurately machined from steel bars or forgings dependent on size. They are crowned to compensate for deflection during forming pressures, assuring accurate cylinders and workpieces. The rolls turn on sealed spherical roller bearings.

IMG_3891 copy.jpg

Dual Guarded Foot Switch

The dual foot switch is a feature available for forward and reverse rotation of the rolls, allowing the operator to use both hands to manipulate workpiece.

IMG_1802_edited.jpg

Beta 3.2 Control

The Beta 3.2 is a manual control and comes with the base machine at no charge.

Push buttons to control:

  • Control

  • Emergency stop

  • Near roll 

  • Far roll

  • Roll rotation

  • Drop end

Selector switch to control:

  • Roll trim

  • Dial to control system speed.

Digital readout to show position of:

  • Near roll

  • Far roll

Features:

  • Free standing rolling console

  • NEMA 12 fiberglass enclosure

  • Stainless steel hand rail

  • Reseptical for control cord

Recommended use, Job Shops and part batches up to 10 pieces

controls_0001_edited.jpg

Single Foot Switch

The single foot switch has a selector to control the function of pinch roll up, rotation forward, and off. This switch is compatible with all controls.

IMG_1800.jpg

Pre 3.2 Control

The Pre 3.2 is a preset control and an upgrade from the Beta 3.2. 

Push buttons to control: 

  • Control

  • Emergency stop

  • Drop end

  • Far roll gauge position

Variable speed joysticks to control:

  • Near roll

  • Far roll

  • Roll rotation

Selector switches to control:

  • Roll trim

  • Set point 1 mode

  • Set point 2 mode

  • Normal mode

Digital readout to show position and control:

  • Near roll (2 set points)

  • Far roll (3 set points)

  • Roll rotation (3 set points)

Features:

  • Free standing rolling console

  • NEMA 12 enclosure

  • Stainless steel hand rail

  • Receptacle for control cord

Recommended use - this popular control provides just enough automation to greatly speed through put performance, and accuracy. It is easily programmed and can be used as manual or preset type control. In many cases this control increases roll performance by 500% or more and is usually all the automation that is required. This control is recommended for part batch sizes from 3 to 100 pieces or more.

controls_0001_edited.jpg

* pictured with optional rotation readout.

*Note, some aspects of the machines have been upgraded since the last brochure revision!

Gallery

Workpiece Accuracy

In the final analysis, the proof of performance is the acceptability of the finished workpiece. With uniform quality of the workpiece blanks, our machines have historically rolled workpieces within 1/2 of 1% of perfect concentricity.

There are many variables that can affect the accuracy and repeatability either minimally or drastically. These include, but are not limited to, the following: varying material thickness; varying material temper; uneven cross section of material, i.e. wide and narrow profile of workpiece or a workpiece with holes or cutouts; and direction of grain of material.

Many of these variables can be overcome by various means. An important element for success is a knowledgeable operator who understands the characteristics of the material being formed and the various functions of the machine. If the workpiece being formed is anything other than uniform material and cylinders, and you are unsure if your pieces can be rolled practically, please provide us with a drawing or sketch and we will be happy to evaluate it.

Publication1horse_edited_edited.jpg

Waldemar Design & Machine L.L.C. warrants its products to be free from defects in material and workmanship for a period of one year from date of manufacture. Waldemar's obligation is to replace, free of charge, any defective part of any product that its inspection shows to be defective, including the lowest priced round trip transportation to Waldemar's plant in Spencer, TN, from any point in the 48 contiguous states. Waldemar shall not be liable for installation and removal expense, loss of time, manufacturing costs, labor, materials, loss of profits, or consequential damages direct or indirect, because of defective products. There is no other warranty, expressed or implied.

Warranty

bottom of page